You can find the FAQ for R10 series and Avius devices below:
R10 AND R10 HYBRID
Make sure that blue light flashes on the VHF-receiver once per second. If the blue light flashes twice per second, press and hold the lower arrow button on the receiver until the device flashes a green light, release the button and the blue light will begin to flicker once a second.
Open your phone’s settings and select “Applications”, from there select Tracker app and go to app permissions. Give permission to the app to always use your own location. Go back to the settings menu of your phone and open your phone's own Bluetooth settings. Connect the receiver to your phone using your phone's own Bluetooth menu.
Open Tracker app and go to devices menu and try to first add the VHF-receiver to the app. If you still cannot connect the receiver, try to restart your phone, and try to add the device again. After you have successfully added the receiver to the app, then add the collar to the app at the same device’s menu.
More information on connecting devices on phone’s Bluetooth can be found for Android OS and for Apple iOS
You will receive an SMS when your device Global SIM-card subscription is ending. You can continue the Global SIM-card subscription from our web store.
It is recommended to continue the subscription before the subscription ends. All purchases will go in line and activate when the remaining subscription ends.
Open the main menu of the app and select "Devices" -> select your device and from the menu select the trash can icon. This will remove the device from the menu and send a factory reset command to the device.
If a green light is illuminating continuously, the device is in factory state and waiting for an admin. Add the device to your application by opening the app -> open the main menu and select "Devices" and tap the plus button to add device -> select the correct device type (R10) -> input all the necessary information and add the device to the application. The green LED-light should stop illuminating in a couple of minutes.
Allow calls in the app on the device settings (Main menu -> Devices -> select the device).
Make sure that the number calling to the device is not a "Private number". The calling phone number should be visible to the R10 device.
Make sure the device is turned on -> open the main menu of the app and select "Devices" -> select your device and select "Bark adjustment". Higher value will make the microphone more sensitive and lower value will make the microphone less sensitive.
AVIUS
Avius VHF-receiver can be attached to one mobile device at a time via Bluetooth.
Tracker app:
Open the main menu and select "Devices" -> select your VHF-receiver and tap the trash can icon. This will release the Bluetooth connection between the mobile device and the VHF-receiver.
If you still cannot connect to the device, you can try to change the connection method of the VHF-receiver by holding the connection button (button with the circular arrows) of the VHF-receiver device for approximately six seconds. The VHF-receiver will flash the green LED-light to inform the user that the Bluetooth mode is changing. Release the button and wait for the device to restart.
After the Bluetooth mode is changed, the blue LED-light of the VHF-receiver will blink once per seconds until the connection has been established to the phone, after which the light will blink once per three seconds. Please note that after changing the Bluetooth mode, you have to reconnect the Avius device.
Tracker app:
Open the main menu and select "Devices". Select your VHF-receiver and remove the device from the app. You can now try to add the device again to the app.
Note! If you still cannot connect to the VHF-receiver, please contact our support.
When adding the collar to the app, make sure that the collar is outside and connected to the satellites (the green LED light on the collar should blink once per three seconds). Also, make sure that you are adding the device by using the correct ID. The Device ID can be found on the first page of the manual or under the collar part on a separate sticker.
If you are still having problems on adding the collar to the app, please contact our support.
The admin user of the device can change the microphone sensitivity.
Open the main menu and select "Devices" -> select your device and select "Bark counter sensitivity". Adjust the sensitivity up to make the microphone more sensitive, and down if you want to adjust the microphone to less sensitive to sounds.
